EXACTLY HOW TO INSTALL A BATHTUB

Exactly How to Install a Bathtub

Exactly How to Install a Bathtub

Blog Article

Book With Us Today!

We have noticed this post pertaining to Installing A Bathtub listed below on the internet and thought it made perfect sense to discuss it with you on this page.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is also a reasonably challenging task. If the old bathtub is readily accessible, the task can move speedily; if you need to open a wall to eliminate the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Opportunities are you may need an expert plumber to make tube connections.
This short article will help you install a new tub in your shower room if you have actually currently acquired a brand-new bathtub as well as do not need to alter the arrangement of your previous supply of water pipes.
Your tools and product list must comprise the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the limited accessibility that is commonly the case.
    Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
    Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making certain that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet ports. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Installing the Bath tub


    Using both wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
    The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the tub up until the spirit level reviews degree.
    To set up faucets, fit the bottom of the furthest flexible tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
    Activate the water as well as examine all joints as well as brand-new pipework for leaks and tighten them if required. Load the bathtub as well as likewise examine the overflow outlet as well as the normal outlet for leakages.
    Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been used at least once as this will certainly resolve it right into its final position.

    Getting ready for the Setup


    First of all, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
    Fit the flexible faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the provided washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final position.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, triggering the water to penetrate the wall between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub Yourself

    As a devoted person who reads about Tools You Need to Install a New Bathtub , I figured sharing that blog post was a smart idea. In case you appreciated our article if you please remember to share it. Thanks for going through it.




    Set Up An Appointment


    Report this page